Top rated products
-
Triggertech Primary Trigger
$164.99
-
TriggerTech Diamond Flat Straight
$304.99
-
TriggerTech Diamond Curved
$304.99
-
BT46-LW17 PSR Atlas Bipod
$309.99
-
BT47-LW17 PSR Atlas Bipod
$329.99
Peterson 28 Nosler Brass
$135.00
50 Pieces per box (BULK PACKAGED)
Due to the packaging and shipping process, case necks are often slightly dinged or bent and need to be rounded up and sized to give proper neck tension. New and/or fired cases must be full-length resized or have the expander ball of the sizing die run through the case neck prior to loading.
Only 1 left in stock
Peterson 28 Nosler Brass
How does the Peterson brass compare to the other makers of 28 Nosler? Recently Peterson tested the three main companies that make the 28 Nosler for sale in the US. The casings we tested, made by those other companies are quite soft.
28 Nosler According to Derek Peterson, president of Peterson Cartridge, “I went online to look for high pressure loads that handloaders are using for 28 Nosler. Specifically, I was looking for loads that were fast and hot. I found a few shooters who are using a load that is close to SAAMI Proof pressure (33% higher than max pressure). Using that load, we loaded up some of our Peterson casings as well as casings from the other leading brands. The picture below shows the results after one firing. So as not to be accusatory, we photoshopped out the company name from the headstamp of the competing brand.”
Peterson continued, “We used the same load in the Peterson brass and the competitor’s brass. Bullets were seated to the same depth in both, and muzzle velocities were within 3 fps of each other. You can see from the photo the pronounced plunger mark on the competitor’s brass. But no mark on the Peterson casing. Other signs of over pressure, in the rival brands we checked, included blown primers and very heavy bolt lift. The primers in the Peterson 28 Nosler brass held fine, and the bolt lift was normal. With one of the rival brands, the case head was so soft you could read the headstamp on the bolt face after it was fired.”
The designers at Peterson are smart about brass grain structure and webbing thickness, and they use that to design casings which:
- hold more pressure.
- get more reloads.
- have longer primer pocket life.
The 28 Nosler is a great long-distance big-game caliber that takes advantage of the newer, high BC, 7mm bullets. In addition to unprimed brass casings Peterson also offers 28 Nosler in loaded ammo.
Additional Information
Warning: Only use Peterson Cartridge Co. casings in firearms in good condition, designed, marked, and chambered for this cartridge. Do not use Peterson Cartridge Co casings for “fire forming” or any other purpose other than what they were designed and tested for. Peterson retains no responsibility for the enclosed casings if they are used outside of the manufacturer’s recommendations.
Peterson Cartridge | Match-Grade Brass Rifle Casings
J&A Outdoors – Firearm Solutions – Shooting Products (jaoutdoors.com)
Related products
-
6.5 SAUM
$107.50Read more50 count box
Standard Annealed Finish
ADG 6.5 SAUM brass
ADG manufactured brass is optimized not only for consistency in performance, but also for durability. One of the ways we accomplished this is by optimizing the material in specific areas to strengthen it. With the optimized material geometry, our brass will generally have a different case volume than most other manufacturer’s brass and therefore will require a different charge weight to achieve the same pressures and velocities. We recommend using a reputable load data source and working up from their recommended minimum starting loads.
We recommend reducing any existing charge weights by 10% and re-developing your specific load when replacing any component in a load recipe with a new component (brass, projectile, primer, or powder type). Failure to reduce charge weights established using other manufacturers brass may result in higher pressures and velocities while using ADG brass and may result in unsafe pressure levels.
-
30 Nosler
$135.00Read more50 count box
Standard Annealed Finish
ADG 30 Nosler
ADG manufactured brass is optimized not only for consistency in performance, but also for durability. One of the ways we accomplished this is by optimizing the material in specific areas to strengthen it. With the optimized material geometry, our brass will generally have a different case volume than most other manufacturer’s brass and therefore will require a different charge weight to achieve the same pressures and velocities. We recommend using a reputable load data source and working up from their recommended minimum starting loads.
We recommend reducing any existing charge weights by 10% and re-developing your specific load when replacing any component in a load recipe with a new component (brass, projectile, primer, or powder type). Failure to reduce charge weights established using other manufacturers brass may result in higher pressures and velocities while using ADG brass and may result in unsafe pressure levels.
-
Sale!
Hornady ELD-X
$35.99 – $49.99Select optionsHornady ELD X Extend your range and never compromise at any distance! The Hornady ELD X (Extremely Low Drag – eXpanding) bullet is a technologically advanced, match accurate, ALL-RANGE hunting bullet featuring highest-in-class ballistic coefficients and consistent, controlled expansion at ALL practical hunting distances. ELD-X® (Extremely Low Drag – eXpanding) – Hornady Manufacturing, Inc Hornady – (jaoutdoors.com) …
-
Sale!
300 RUM
$112.99 – $119.99Select options50 count box
300 Rem Ultra Mag
ADG manufactured brass is optimized not only for consistency in performance, but also for durability. One of the ways we accomplished this is by optimizing the material in specific areas to strengthen it. With the optimized material geometry, our brass will generally have a different case volume than most other manufacturer’s brass and therefore will require a different charge weight to achieve the same pressures and velocities. We recommend using a reputable load data source and working up from their recommended minimum starting loads.
We recommend reducing any existing charge weights by 10% and re-developing your specific load when replacing any component in a load recipe with a new component (brass, projectile, primer, or powder type). Failure to reduce charge weights established using other manufacturers brass may result in higher pressures and velocities while using ADG brass and may result in unsafe pressure levels.
