Top rated products
-
Triggertech Primary Trigger
$164.99
-
TriggerTech Diamond Flat Straight
$304.99
-
TriggerTech Diamond Curved
$304.99
-
BT46-LW17 PSR Atlas Bipod
$354.95
-
BT47-LW17 PSR Atlas Bipod
$374.95
7mm Remington Magnum
$93.00 – $97.65
50 count box
7mm REM MAG BRASS
ADG manufactured brass is optimized not only for consistency in performance, but also for durability. One of the ways we accomplished this is by optimizing the material in specific areas to strengthen it. With the optimized material geometry, our brass will generally have a different case volume than most other manufacturer’s brass and therefore will require a different charge weight to achieve the same pressures and velocities. We recommend using a reputable load data source and working up from their recommended minimum starting loads.
We recommend reducing any existing charge weights by 10% and re-developing your specific load when replacing any component in a load recipe with a new component (brass, projectile, primer, or powder type). Failure to reduce charge weights established using other manufacturers brass may result in higher pressures and velocities while using ADG brass and may result in unsafe pressure levels.
7mm Remington Magnum
Additional information
| CALIBER | 28, 7mm |
|---|---|
| FINISH | Bright, Standard |
| QUANTITY | Retail Box (50 pc) |
| CASE WEIGHT | 240.6 grains (average) |
| CASE VOLUME | 82.3 grains/H2O (average) |
| NECK WALL THICKNESS | .0132″ (average) |
Premium Rifle Cartridge Cases –
All 7mm Remington Magnum ADG Brass is offered in a 50 piece retail box that utilizes a custom ammo box and foam liner to protect the brass during shipment. These boxes are made in the USA and can be reused to store and transport your loaded ammo.
Our brass is tracked with a custom lot number for quality control which is located on the underside of box.
About Us
Headquartered in Elizabethtown, KY and owned and operated by six experienced, industry professionals and a staff with over 200 years of combined experience, our skill set covers the full spectrum of required disciplines: mechanical engineering, metallurgical engineering, electrical engineering, industrial design, CAD design, and an Associate in Applied Science Degree in Gunsmithing.
Utilizing Six Sigma® methodologies and procedures, decades of experience, the latest equipment technology available and unrivaled data management, ADG can tackle a broad range of product development challenges, from slight twists on classic designs to the most complex and innovative technologies.
Backed by ADG’s product development business unit, we not only identify underlying issues, we can also determine and implement solutions from design all the way to the production environment. Our design and metallurgical engineers can provide superior failure analysis, design investigative experiments, and provide design direction.
J&A Outdoors – Firearm Solutions – Shooting Products (jaoutdoors.com)
| Weight | 16 oz |
|---|---|
| Dimensions | 8 × 6 × 4 in |
| Finish: | Standard (anneal line), Shiny |
Related products
-
Sale!
300 PRC
Original price was: $97.85.$88.07Current price is: $88.07.Add to cart50 count box
Standard Annealed Finish
ADG 300 PRC
ADG manufactured brass is optimized not only for consistency in performance, but also for durability. One of the ways we accomplished this is by optimizing the material in specific areas to strengthen it. With the optimized material geometry, our brass will generally have a different case volume than most other manufacturer’s brass and therefore will require a different charge weight to achieve the same pressures and velocities. We recommend using a reputable load data source and working up from their recommended minimum starting loads.
We recommend reducing any existing charge weights by 10% and re-developing your specific load when replacing any component in a load recipe with a new component (brass, projectile, primer, or powder type). Failure to reduce charge weights established using other manufacturers brass may result in higher pressures and velocities while using ADG brass and may result in unsafe pressure levels.
-
28 Nosler
$137.50Add to cart50 count box
Standard Annealed Finish
ADG 28 Nosler
ADG manufactured brass is optimized not only for consistency in performance, but also for durability. One of the ways we accomplished this is by optimizing the material in specific areas to strengthen it. With the optimized material geometry, our brass will generally have a different case volume than most other manufacturer’s brass and therefore will require a different charge weight to achieve the same pressures and velocities. We recommend using a reputable load data source and working up from their recommended minimum starting loads.
We recommend reducing any existing charge weights by 10% and re-developing your specific load when replacing any component in a load recipe with a new component (brass, projectile, primer, or powder type). Failure to reduce charge weights established using other manufacturers brass may result in higher pressures and velocities while using ADG brass and may result in unsafe pressure levels.
-
338 Lapua
$145.00Read more50 count box
Standard Annealed Finish
ADG 338 Lapua
ADG manufactured brass is optimized not only for consistency in performance, but also for durability. One of the ways we accomplished this is by optimizing the material in specific areas to strengthen it. With the optimized material geometry, our brass will generally have a different case volume than most other manufacturer’s brass and therefore will require a different charge weight to achieve the same pressures and velocities. We recommend using a reputable load data source and working up from their recommended minimum starting loads.
We recommend reducing any existing charge weights by 10% and re-developing your specific load when replacing any component in a load recipe with a new component (brass, projectile, primer, or powder type). Failure to reduce charge weights established using other manufacturers brass may result in higher pressures and velocities while using ADG brass and may result in unsafe pressure levels.
